TEC
Time Enforcement Commission
It should be mentioned, however, that before a (time displacement) can occur, the circuit must first be connected to a variable 44-volt DC power supply. Also while using the (S2) push button switch, the voltage must be pulsed at 2 cycles per second. If a lesser voltage is used, and the current is pulsed at a different frequency, then the most that you will be able to accomplish, or at least in most cases, is an out-of-the-body experience. The place in which to purchase most of these components can be brought through (Skycraft Electronics). Their telephone number is: (407) 628-5634. However, as for the 1M ohm 10W potentiometer and the piezo transducer, both of these items can be obtained through your local Radio Shack store. The dials to be used should be numbered from 0 to 100. These dials can be obtained through (Newark Electronics). Their number is: (402) 392-1055.
Now to operate this device, first of all, activate the variable 44 volt DC power supply. Next, move the (S3) switch to either the past or future mode. Now for future time travel, set vr1 at 10 meters and vr2 at the highest possible setting. Next, while the piezo transducer is taped over the navel area, turn vr2 backward from 84 to 0 while pressing the (S2) push button switch in an up-and-down motion so that the current is pulsed at 2 cycles per second. When you hit the correct setting on VR2, you still hear some sort of clicking or popping noise. As soon as you hear this click or pop, the hour hands on your wall clock (that is, if you have one) should move forward or backward in time. Thus, by watching the wall clock, we can therefore arrive at the date of our choosing, that is, if the theory holds. If not, then another means will have to be devised, to determine the time and place in which you will land in.
As for past time travel, vr2 is left on (0), and vr1 is turned slowly from 0 to 84 while pressing the (S2) push button switch in an up-and-down motion. As before, as soon as you hear the click or pop, you should be moving through time. Remember! As soon as you arrive at the destination point, deactivate the power switch, because if you don't, you'll just keep on going. Note:- This same rule applies if you decide to travel into the future.
It should also be mentioned, that this device will not work for everyone. The reason for this is quite simple. The brain waves must oscillate at a certain frequency before a time displacement can occur. Thus, there is only going to be something like a few people out of a hundred who are going to get any results. This may also have a lot to do with the individual's faith. A detailed schematic of this device is in this page. If you will note, a frequency or pulse generator may be used in place of the variable 44-volt DC transformer. However, you may only get an out-of-the-body experience.
1. For physical time travel, activate the flux capacitor over an artificial grid point.
2. If a 9-volt battery is used as the power source, it may take as long as 40 minutes, before the person can travel physically through time. In other words, it takes a while before the capacitor builds up a charge.
3. Grid points can be avoided if a (double terminated quartz crystal) is placed somewhere in the circuit.
4. To program a quartz crystal for physical time travel, use a pendulum.
5. To increase its performance, place a (caduceus coil) around the crystal. When doing this, make certain that the coils are wrapped evenly. If they're not, there may be trouble.
6. It is possible to use the Flux Capacitor for physical time travel, without having the current pulsed at two cycles per second. In some ways, it may even work better.
7. By connecting an ELF circuit to the flux capacitor, you could pulse the current at 7.8 Hz., c.p.s. This would greatly improve its performance.
Now to operate this device, first of all, activate the variable 44 volt DC power supply. Next, move the (S3) switch to either the past or future mode. Now for future time travel, set vr1 at 10 meters and vr2 at the highest possible setting. Next, while the piezo transducer is taped over the navel area, turn vr2 backward from 84 to 0 while pressing the (S2) push button switch in an up-and-down motion so that the current is pulsed at 2 cycles per second. When you hit the correct setting on VR2, you still hear some sort of clicking or popping noise. As soon as you hear this click or pop, the hour hands on your wall clock (that is, if you have one) should move forward or backward in time. Thus, by watching the wall clock, we can therefore arrive at the date of our choosing, that is, if the theory holds. If not, then another means will have to be devised, to determine the time and place in which you will land in.
As for past time travel, vr2 is left on (0), and vr1 is turned slowly from 0 to 84 while pressing the (S2) push button switch in an up-and-down motion. As before, as soon as you hear the click or pop, you should be moving through time. Remember! As soon as you arrive at the destination point, deactivate the power switch, because if you don't, you'll just keep on going. Note:- This same rule applies if you decide to travel into the future.
It should also be mentioned, that this device will not work for everyone. The reason for this is quite simple. The brain waves must oscillate at a certain frequency before a time displacement can occur. Thus, there is only going to be something like a few people out of a hundred who are going to get any results. This may also have a lot to do with the individual's faith. A detailed schematic of this device is in this page. If you will note, a frequency or pulse generator may be used in place of the variable 44-volt DC transformer. However, you may only get an out-of-the-body experience.
1. For physical time travel, activate the flux capacitor over an artificial grid point.
2. If a 9-volt battery is used as the power source, it may take as long as 40 minutes, before the person can travel physically through time. In other words, it takes a while before the capacitor builds up a charge.
3. Grid points can be avoided if a (double terminated quartz crystal) is placed somewhere in the circuit.
4. To program a quartz crystal for physical time travel, use a pendulum.
5. To increase its performance, place a (caduceus coil) around the crystal. When doing this, make certain that the coils are wrapped evenly. If they're not, there may be trouble.
6. It is possible to use the Flux Capacitor for physical time travel, without having the current pulsed at two cycles per second. In some ways, it may even work better.
7. By connecting an ELF circuit to the flux capacitor, you could pulse the current at 7.8 Hz., c.p.s. This would greatly improve its performance.
Last edited by a moderator: